Product inquiry
SKY RC Brushless Motor Tester, NEW
Goods code: 3SK5020
Set availability monitoring
SKY RC Brushless Motor Tester, NEW
Goods code: 3SK5020
SKY RC Brushless Motor Tester, NEW
| Price in e-shop with VAT: | 102,05 € |
| Temporarily unavailable | |
|
|
Send a question
on availability |
|
Send a question
on availability |
|
|
35 years in business = safe shopping and professional service |
|
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
#Chcete dostat upozornění ve chvíli, kdy produkt bude k dispozici? Stačí vyplnit formulář a náš hlídací pes Vám dá vědět.
-
Product Description
-
Technical Data:
Product Description
SKY RC 3SK5020 - SKY RC Brushless Motor Tester, NEW
The SKY RC Motor Analyzer BMA-01 brushless motor tester is an electronic device specially designed to measure parameters such as revolutions per volt (“KV”), motor RPM, current draw, timing (average and individual phase values), noise level, and the functionality of Hall sensors in brushless motors. Measurements for both sensored and sensorless brushless motors are displayed in real time on a two-line LCD.
The tester is primarily designed for 2- and 6-pole motors in the conventional configuration (“inrunners”) used in RC car models, with a maximum current draw of 30 A. Motors with other pole counts (2–36 poles) and rotating-can motors (“outrunners”) can also be measured, but operation with some types of outrunner may not be guaranteed.
The tester includes a holder for mounting the motor under test (inrunner). A 2-cell LiPo battery with a capacity of at least 2000 mAh is required to power the tester.
1. Testing sensored and sensorless brushless motors
In motor test mode, the motor under test is secured in the tester’s holder. Connect the motor power leads and, if applicable, the sensor cable to the corresponding sockets on the tester. Set the number of poles of the motor being measured in the software. When measurement starts, the tester automatically provides a soft start at low RPM; you can then increase the motor speed up to maximum by turning the 3D dial – the throttle level is indicated by an LED bar. The Motor Analyzer measures:
- Supply voltage
- Revolutions per volt (KV), with an accuracy of +/-3%
- Motor RPM
- Motor current draw (up to 30 A)
2. Timing measurement
The tester measures motor timing, providing both an average value for the entire motor and values for the sensors of individual phases A, B and C. This allows you to fine-tune the timing very precisely (ideally, the values for all three phases should be the same).
3. Noise measurement
A poorly manufactured or assembled motor, inferior or worn bearings, a bent shaft, an unbalanced rotor and other mechanical defects can generate vibrations. Motor vibrations set the surrounding air in motion – these vibrations are sound waves that we perceive as motor noise.
The higher the vibration level, the more negatively motor performance is affected. By measuring motor noise with the built-in measurement microphone, you can choose the unit with the lowest vibration level – i.e. the lowest losses.
4. Hall sensor testing (for sensored motors only)
This mode checks that the Hall sensors detecting rotor position are functioning correctly – this is critical for the ESC to control the motor properly. For example, the tester can help you detect a faulty sensor or motor power leads connected in the wrong order.
The tester set includes: Motor Analyzer BMA-01, XT60/4 mm banana plug power cable, XT60/Tamiya power cable, six-wire sensor cable, instructions.
Technical Data:
| Power supply | 7.4–8.4 V (2S LiPo) |
| Supported motor types | Sensored and sensorless brushless motors (2–36 poles) |
| KV measurement accuracy | ±3% |
| Timing measurement accuracy | ±4% |
| Timing measurement range | 0–70° |
| Noise measurement range | 60–120 dB |
| Max. motor current draw | max. 30 A at 8.4 V |
| Dimensions | 136.5x80.6x24.5 mm |
| Weight | 282 g |