Futaba 10J with R3008SB receiver (Mode 1)
Wednesday 25.11. it can be at your place
Customer line 9 am - 6 pm: +420 774 590 258 | Do you need help?
| Price in e-shop with VAT: | 286,48 € |
| Stock 1 pcs | |
|
|
Buy |
| Buy | |
|
35 years in business = safe shopping and professional service |
|
| YOU CAN HAVE IT IN STORE NOW: | |
| Nademlejnská - eshop | 1 pcs |
| Tuesday 24.11. it can be at your place |
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
Send a question3D aerobatic motor glider with a 1512 mm wingspan, made from virtually indestructible, carbon-reinforced extruded polyolefin foam (EPO). Fitted with a C2820-1450 brushless motor, 7×6" folding propeller, R-20B Plus ESC and 4 metal-geared micro servos. Features a controlled rudder, full-flying elevator and full-flying wing halves.
With our new Twisty 3D aerobatic motor glider, you can really have fun flying on flat ground as well as on slopes. It not only has large control surfaces, as is usual with 3D models, but, in addition to a full-flying elevator, it is also equipped with full-flying wings.
Twisty feels right at home on mountain slopes, coastal cliffs or dunes, where it can really show what it can do in strong winds. So you can enjoy it even where the hills are not very high and the wind is only moderate, we have added a powerful brushless motor with a folding propeller.
Fuselage
The model's fuselage is made of highly durable EPO foam (extruded polyolefin) with robust internal carbon reinforcements. The nose is fitted with a C2820-1450 brushless electric motor with a 7×6“ folding propeller and a Kavan R-20SB Plus ESC.
Wing
The model's EPO foam wing is made in two parts and reinforced with carbon. The wing halves slide onto a carbon tube joiner and are secured in place with screws. The wings are controlled independently by two servos with short, straight wire pushrods. For easy neutral-position adjustment, triangular markings on the fuselage indicate the center position of the trailing edge.
Tail surfaces
The tail surfaces are also made of EPO foam and reinforced with carbon. The horizontal tail is full-flying; its halves slide onto a carbon tube joiner and are secured with screws. For easy neutral-position adjustment, triangular markings on the fuselage indicate the center position of the elevator's leading edge.
Canopy
The canopy is removable and secured with a pin at the front and a mechanical latch at the rear. There is plenty of room in the nose for the flight battery and receiver. The metal-geared micro servos controlling the wing halves, rudder and elevator are housed in the area under the wing.
Recommended flight battery
You will need a 3S LiPo flight battery with a capacity of 1300 mAh and a discharge rating of at least 30C, fitted with an XT60 power connector. Choose a specific type that provides the correct center of gravity position with as little additional ballast as possible.
Recommended RC system
To control the model, you will need at least a 6-channel computer radio system that allows independent control of the wing halves (ailerons) with two servos and has an elevator-flaperon (camber) mix to increase maneuverability.
The manual naturally includes a detailed table of tested initial control surface throws (including mixes), so you can easily get Twisty ready to fly.
Package contents
The package contains a finished fuselage, wings and tail surfaces made of EPO foam, as well as an installed motor, propeller, ESC and 4 servos. An instruction manual is also included.
Notice: Under Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems, and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (traditional model aircraft, multicopters, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic with the Civil Aviation Authority). You can find more information here: Registration of drone operators and pilots.
| Span [mm] | 1512 |
| Length [mm] | 1005 |
| Weight [g] | 735–750 |
| Wing area [dm 2 ] | 23.8 |
| Controlled functions | S, V, K (2), M |
| Difficulty of construction | S0, S1 |
| Piloting difficulty | P2, P3 |
11 items
This website is using cookies
In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.