Futaba 10J with R3008SB receiver (Mode 1)
Wednesday 25.11. it can be at your place
Customer line 9 am - 6 pm: +420 774 590 258 | Do you need help?
| Price in e-shop with VAT: | 286,48 € |
|
Stock
Tuesday 24.11. you can have it at the Nademlejnská central store Wednesday 25.11. it can be at your place |
|
|
|
Buy |
| Buy | |
|
35 years in business = safe shopping and professional service |
|
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
Send a question3D aerobatic motor glider with a 1512 mm wingspan, made from virtually indestructible, carbon-reinforced extruded foam polyolefin (EPO). Equipped with a C2820-1450 brushless motor, 7×6" folding propeller, R-20B Plus ESC and 4 metal-geared micro servos. Features a rudder, full-flying elevator and full-flying wing halves.
Our new 3D aerobatic motor glider, Twisty, lets you really have fun flying on flat ground and slopes alike. It has not only the large control surfaces typical of 3D models, but, in addition to a full-flying elevator, it also features full-flying wing panels.
Twisty feels right at home on mountain slopes, coastal cliffs or dunes, where it can really show what it can do in strong winds. To let you enjoy it even where the hills are not very high and the wind is only light, we have added a powerful brushless motor with a folding propeller.
Fuselage
The model’s fuselage is made from highly durable EPO foam (extruded polyolefin) with thorough internal carbon reinforcements. A C2820-1450 brushless electric motor with a 7×6“ folding propeller and a Kavan R-20SB Plus ESC are installed in the nose.
Wing
The model’s EPO foam wing is made in two sections and reinforced with carbon. The wing halves slide onto a carbon tube joiner and are secured in place with screws. The wings are controlled independently by two servos with short, straight wire pushrods. Triangular marks on the fuselage indicate the centre position of the trailing edge for easy neutral position adjustment.
Tail surfaces
The tail surfaces are also made from EPO foam and reinforced with carbon. The horizontal tailplane is full-flying; its halves slide onto a carbon tube joiner and are secured with screws. Triangular marks on the fuselage indicate the centre position of the elevator’s leading edge for easy neutral position adjustment.
Canopy
The canopy is removable and secured with a pin at the front and a mechanical latch at the rear. There is plenty of room in the nose for the flight battery and receiver. The metal-geared micro servos that control the wing halves, rudder and elevator are housed in the space beneath the wing.
Recommended flight battery
You will need a 3S LiPo flight battery with a capacity of 1300 mAh and a discharge rating of at least 30C, fitted with an XT60 power connector. Choose a specific type that gives you the correct centre of gravity as closely as possible without additional balancing.
Recommended RC system
To control the model, you will need at least a 6-channel computerised RC system that allows independent control of the wing halves (ailerons) using two servos. For greater manoeuvrability, it should have an elevator-flaperon (camber) mix.
The manual also includes a comprehensive table of proven initial control surface settings (including mixes), so you can easily get Twisty ready to fly.
Package contents
The package contains a completed fuselage, wings and tail surfaces made from EPO foam, as well as an installed motor, propeller, ESC and 4 servos. The instruction manual is also included.
Warning: Under Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems, and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (conventional model aircraft, multicopters, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic, with the Civil Aviation Authority). You can find more information here: Registration of drone operators and pilots.
| Span [mm] | 1512 |
| Length [mm] | 1005 |
| Weight [g] | 735–750 |
| Wing area [dm 2 ] | 23.8 |
| Controlled functions | S, V, K (2), M |
| Difficulty of construction | S0, S1 |
| Piloting difficulty | P2, P3 |
11 items
This website is using cookies
In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.