Kavan Pulse 2200 V2: Canopy
Wednesday 25.11. it can be at your place
Customer line 9 am - 6 pm: +420 774 590 258 | Do you need help?
| Price in e-shop with VAT: | 347,95 € |
|
Stock
Tuesday 24.11. you can have it at the Nademlejnská central store Wednesday 25.11. it can be at your place |
|
|
|
Buy |
| Buy | |
|
35 years in business = safe shopping and professional service |
|
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
Send a questionA practically ready-to-fly model of a fast and agile powered glider with a 2206 mm wingspan, made of extruded polyolefin foam (EPO), for thermal and slope soaring. The model is equipped with a C3548-750 brushless motor, a Kavan R-50SB Plus ESC and 6 servos. Ailerons, rudder, elevator, flaps and motor speed are controlled.
Your favourite Pulse 2200 is back in a V2 version – nimble and agile, with new, stronger and faster servos and a range of other improvements, such as precision ball links on the control rods, so nothing gets in the way of your fun on the slope or on flat ground!
The Pulse 2200 V2 has a fully mechanised wing with ailerons and flaps, a robust, carbon-reinforced EPO foam construction, and plenty of power for aerobatic and slope flying thanks to its brushless motor.
It is the perfect recreational aircraft, offering plenty of fun for any pilot with at least a little experience!
The model's fuselage is made of highly durable, thoroughly reinforced EPO foam (extruded polyolefin). A C3548-750 brushless electric motor with an 11×8“ folding propeller is installed in the nose.
The Kavan R-50SB Plus ESC with a powerful BEC stabiliser powers the 6 onboard servos. The canopy cover is removable and secured with a pin at the front and a magnet at the rear. There is plenty of room in the nose for the flight battery and receiver. The rudder and elevator servos are housed in the rear section of the fuselage and control the surfaces using short wire pushrods.
The EPO foam wing is in two sections and has carbon spars, the protruding parts of which also serve as the wing joiner. The wing halves are secured in place with a plastic screw. The ailerons (reinforced with a carbon strip) and flaps are each controlled independently by two servos with short wire pushrods.
The tail surfaces are also made of EPO foam, with carbon strip reinforcements. The two-piece horizontal tailplane is attached to the fin using a carbon joiner and a pair of screws for easy assembly and disassembly.
For power, you will need a 4S LiPo battery with a capacity of 2600–4000 mAh, rated at least 30C and fitted with an XT60 power connector. Choose a specific type that will give you the correct centre of gravity position with as little additional ballast as possible.
You can control the model with a basic 6-channel computerised RC system without special functions if necessary. In the standard configuration, the ailerons and flaps are connected to a single channel each via cables with multi-connectors.
Ideally, use at least a 7-channel computerised RC system that allows independent control of the ailerons and flaps with two servos and mixing them as a butterfly brake (both ailerons deflect upwards together and both flaps downwards).
In this case, the aileron and flap servos must be connected separately. The manual includes a detailed table of tested initial control surface settings, making it easy to prepare the Pulse 2200 V2 for flight.
Package contents
The package contains the ready-made fuselage, wing and tail surfaces made of EPO foam, with the motor, propeller, ESC and 6 servos installed. A clear manual is also included, of course.
Warning: Under Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (conventional model aircraft, multicopters, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic with the Civil Aviation Authority). More information can be found here: Registration of drone operators and pilots.
| Wingspan [mm] | 2206 |
| Length [mm] | 1266 |
| Weight [g] | 2100–2250 |
| Wing area [dm2] | 41,8 |
| Controlled functions | S, V, K (2), M, F (2) |
| Build difficulty | S0, S1 |
| Piloting difficulty | P2, P3 |
10 items
This website is using cookies
In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.