Kavan Beta 1400: Držák motoru
unavailable
Customer line 9 am - 6 pm: +420 774 590 258 | Do you need help?
| Price in e-shop with VAT: | 257,79 € |
| Temporarily unavailable | |
|
|
Send a question
on availability |
|
Send a question
on availability |
|
|
35 years in business = safe shopping and professional service |
|
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
#Chcete dostat upozornění ve chvíli, kdy produkt bude k dispozici? Stačí vyplnit formulář a náš hlídací pes Vám dá vědět.
Almost ready-to-fly, high-performance thermal glider with a 1800 mm wingspan, made of virtually indestructible extruded foam polyolefin (EPO), with a carbon tail boom. It is equipped with a C2714-1450 brushless motor with a folding 7×6" propeller, an R-20B speed controller and 4 micro servos. Ailerons, rudder, elevator and motor speed are controlled. A Kavan R6 receiver is also included.
Model aircraft are generally created as scaled-down versions of real, “full-size” aircraft. Our designers took a different approach, however: they kept watering, hoeing and treating the popular Der Kleine Falke model with 100% biological products until it grew to a wingspan of 1800 mm and became the high-performance thermal RC glider Falke 1800.
The front section of the model’s fuselage is made of highly durable EPO foam (extruded polyolefin). The tail boom is made from a carbon tube. A C2714-1450 brushless electric motor with a folding 7×6“ propeller and a Kavan R-20B speed controller with a BEC power supply stabilizer are installed in the nose.
The canopy hatch is removable and secured with a pin at the front and a magnet at the rear. There is plenty of room in the nose for the power battery and receiver. The rudder and elevator servos are housed in the fuselage beneath the wing, and the control surfaces are operated by pushrods.
The model’s EPO foam wing is two-piece, with a carbon spar and a steel wire joiner; it is attached to the fuselage with two plastic screws. The ailerons are controlled independently by two servos with short, straight wire pushrods. The removable V-tail surfaces are also made of EPO foam and are attached to the fuselage with a plastic screw.
The model is powered by a C2714-1450 brushless motor with a 20A Kavan R-20B speed controller. For power, you will need a 3-cell LiPo battery with a capacity of 1200–1600 mAh and a discharge rating of at least 20C, fitted with an XT60 power connector. Choose a specific battery type that will give you the correct centre of gravity position without requiring additional ballast.
In a pinch, a four-channel transmitter with the ACCESS / ACCST D16 protocol and a V-tail mix will suffice to control the model—in the basic configuration, the ailerons are connected to a single channel using a Y-cable.
Ideally, of course, use at least a six-channel transmitter with the ACCESS / ACCST D16 protocol, which allows the two aileron servos to be controlled independently and mixed to act as an aerodynamic brake (both ailerons deflect upwards together).
In that case, replace the aileron Y-cable in the fuselage with two extension cables (15–30 cm). The manual naturally includes a detailed table of tested initial control-surface deflection settings (including mixes), so you can easily prepare the Falke for flight.
Package contents
The ARF set contains a finished fuselage, wing and tail surfaces made of EPO foam, with the motor, propeller, speed controller and 4 servos installed. A Kavan R6 receiver and a clear manual are also included.
Warning: Under Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems, and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (conventional model aircraft, multicopters, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic, with the Civil Aviation Authority). Further information is available here: Registration of drone operators and pilots.
| Wingspan [mm] | 1800 |
| Length [mm] | 1150 |
| Weight [g] | 660–710 |
| Wing area [dm2] | 27 |
| Controlled functions | S, V, K (2), M |
| Build difficulty | S0, S1 |
| Pilot skill level | P1, P2 |
Power system and RC equipment:
| Motor | *) C2714-1450 |
| Speed controller | *) Kavan R-20B |
| Propeller blades | *) 7×6“ |
| Recommended battery | Kavan 11,1V 1200 mAh 30/60C, or Kavan 11,1V 1600 mAh 30/60C |
| Servos | *) 4× GO-09 |
| Receiver | *) Kavan R6 |
| RC system | At least 4 channels with a V-tail mix |
| *) Included in the ARF set | |
11 items
This website is using cookies
In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.