Kavan Swift S-1 2400mm BNF with Kavan R8 Vario receiver (blue)

Price in e-shop with VAT: 499,59 €
Temporarily unavailable
Send a question
on availability
Send a question
on availability

35 years in business = safe shopping and professional service
Manufacturer: Kavan
Goods code: KAV02.8082C
EAN:

Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
#Chcete dostat upozornění ve chvíli, kdy produkt bude k dispozici? Stačí vyplnit formulář a náš hlídací pes Vám dá vědět.

Send a question Watch availability
  • Product Description

  • Technical Data:

Product Description

Kavan KAV02.8082C - Kavan Swift S-1 2400mm BNF with Kavan R8 Vario receiver (blue)

A practically ready-to-fly semi-scale model of a high-performance Polish aerobatic glider with a 2400 mm wingspan, made of almost indestructible, carbon-reinforced extruded polyolefin foam (EPO), for thermal and slope soaring. Equipped with a C3548-750 brushless motor, 11×8" folding propeller, Kavan R-50SB ESC and 4 micro servos. Ailerons, rudder, elevator and motor speed are controlled. A Kavan R8 Vario telemetry receiver is also included in the package.

In the late 1980s, the Polish company Margański & Mysłowski Zakłady Lotnicze concluded that there was a gap in the aerobatic glider market—the good old all-wood SZD-21-2b Kobuz 3, designed in the 1950s, was no longer quite up to the task. So, in 1991, designers Edward Margański and Jerzy Cisowski, supported by Jerzy Makula (at the time a three-time world champion in aerobatic gliding), introduced the new Swift S-1, a modern all-composite aerobatic glider with an incredible roll rate (just 4 s), capable of handling loads of +/-10 g. The reward came almost immediately—Jerzy Makula won his fourth FAI World Aerobatic Gliding Championship title that same year.

The model’s fuselage is made of highly durable EPO (extruded polyolefin) foam, with substantial internal carbon reinforcements. A C3548-750 brushless electric motor with an 11×8“ folding propeller and a Kavan R-50SB ESC with a high-performance BEC stabilizer is installed in the nose, providing the power needed for the 4 powerful micro servos.

The canopy cover is removable and secured by a pin at the front and a magnet at the rear. The nose has plenty of room for the flight battery and receiver. The rudder and elevator servos are housed in the fin, and control the surfaces using short, straight wire pushrods.

The model’s EPO foam wing is in two pieces and fitted with carbon spars. Their protruding ends also serve as the wing joiner, fitting into duralumin sleeves in the fuselage. The wing halves are secured in place with a plastic screw. The full-span ailerons (reinforced with carbon tubes) are controlled independently by two servos using short, straight wire pushrods.

The tail surfaces are also made of EPO foam and reinforced with carbon tubes. The horizontal tailplane is attached to the fuselage with two screws for easy assembly and disassembly.

Package contents

The package contains a finished EPO foam fuselage, wing and tail surfaces, with the motor, propeller, ESC and 4 servos installed, a Kavan R8 Vario telemetry receiver and Czech-language instructions.

Required to complete

You will need a 4-cell LiPo battery with a capacity of 2200–2700 mAh and a discharge rating of at least 30C. Choose a specific type that will give you the correct centre of gravity position with as little additional balancing as possible. You will also need a suitable charger to charge the flight battery.

In a pinch, you can control the model with a 4-channel transmitter using the ACCESS / ACCST D16 protocol and no special functions. In the basic configuration, the ailerons are connected to a single channel using a Y-cable. Ideally, use a computer transmitter with at least 6 channels, allowing independent control of the ailerons by two servos and mixing them as an aerodynamic brake (both ailerons deflect upwards together).

In this case, replace the aileron Y-cable in the fuselage with two extension leads (15–30 cm). The instructions also include a detailed table of proven initial control surface deflection settings (including mixes) to make it easy to prepare the model for flight.

Warning: Under Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems, and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (conventional model aircraft, multirotors, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic, with the Civil Aviation Authority). Further information is available here: Registration of drone operators and pilots.

Technical Data:

Wingspan [mm] 2405
Length [mm] 1300
Weight [g] 2000–2050
Wing area [dm2] 45
Controlled functions S, V, K (2), M
Build difficulty S0, S1
Piloting difficulty P2

Recommended power system and RC equipment

Motor *) C3548-750
ESC *) KAVAN R-50SB
Propeller blades *) 11×8“
Battery 14,8V 2200mAh 30/60C, 14,8V 2600mAh 40/80C
Servos *) 4× GO-17MG
Receiver *) Kavan R8 Vario
RC system Min. 6 channels (computer transmitter)
*) Included in the ARF set

Related products

10 items

This website is using cookies

In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.