Gens Ace LiPo Tattu Series - 4S 2300mAh 14,8V 4S1P (75C) XT60 Plug
Customer line 9 am - 6 pm: +420 774 590 258 | Do you need help?
| Price in e-shop with VAT: | 409,43 € |
|
Stock
Tuesday 24.11. you can have it at the Nademlejnská central store Wednesday 25.11. it can be at your place |
|
|
|
Buy |
| Buy | |
|
35 years in business = safe shopping and professional service |
|
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
Send a questionA practically ready-to-fly semi-scale model of a powerful Polish aerobatic glider with a 2400 mm wingspan, made from almost indestructible, carbon-reinforced extruded foam polyolefin (EPO), for thermal and slope soaring. Equipped with a C3548-750 brushless motor, 11×8" folding propeller, Kavan R-50SB speed controller and 4 micro servos. Controls ailerons, rudder, elevator and motor speed.
In the late 1980s, the Polish company Margański & Mysłowski Zakłady Lotnicze concluded that there was a gap in the aerobatic glider market—the good old all-wood SZD-21-2b Kobuz 3, designed in the 1950s, was no longer up to the task. So, in 1991, designers Edward Margański and Jerzy Cisowski, supported by Jerzy Makula (at the time a three-time world champion in glider aerobatics), introduced the new Swift S-1, a modern all-composite aerobatic glider with an incredible roll rate (just 4 s) and capable of withstanding +/−10 g. The reward came almost immediately—Jerzy Makula won his fourth FAI World Glider Aerobatics Championship title that same year.
The model's fuselage is made of highly durable EPO foam (extruded polyolefin), with substantial internal carbon reinforcements. The nose houses a C3548-750 brushless electric motor with an 11×8“ folding propeller and a Kavan R-50SB controller with a powerful BEC stabilizer, required to power the 4 high-performance micro servos.
The canopy hatch is removable and secured with a pin at the front and a magnet at the rear. There is plenty of space in the nose for the flight battery and receiver. The rudder and elevator servos are housed in the fin, and operate the control surfaces via short, straight wire pushrods.
The model's EPO foam wing is built in two sections and equipped with carbon spars, whose protruding ends also serve as the wing joiner, fitting into duralumin sleeves in the fuselage. The wing halves are secured in place with a plastic screw. Full-span ailerons (reinforced with carbon tubes) are controlled independently by two servos using short, straight wire pushrods.
The tail surfaces are also made of EPO foam, with carbon tube reinforcements. The horizontal tail is attached to the fuselage with two screws for easy assembly and removal.
Package contents
The package contains a ready-made fuselage, wing and tail surfaces made of EPO foam, with the motor, propeller, speed controller and 4 servos installed. A Czech-language manual is also included.
Required to complete
You will need a 4-cell LiPo battery with a capacity of 2200–2700 mAh and a discharge rating of at least 30C. Choose a specific type that gives you the correct centre of gravity position with as little additional ballast as possible. You will also need a suitable charger to charge the flight battery.
In a pinch, you can control the model with a 4-channel computer radio system without special functions. In the basic configuration, the ailerons are connected to a single channel using a Y-cable. Naturally, it is best to use at least a 6-channel computer radio system, allowing independent control of the ailerons with two servos and mixing them as an aerodynamic brake (both ailerons deflect upwards together). Affordable systems such as the Radiolink AT9S or AT10II, or the Futaba T6K or T10J, offer this feature.
In this case, replace the aileron Y-cable in the fuselage with two extension leads (15–30 cm). The manual naturally includes a detailed table with tested initial control-surface throws (including mixes), so you can easily prepare the model for flight.
Notice: According to Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems, and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (traditional model aircraft, multicopters, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic, with the Civil Aviation Authority). Further information is available here: Registration of drone operators and pilots.
| Wingspan [mm] | 2405 |
| Length [mm] | 1300 |
| Weight [g] | 2000–2050 |
| Wing area [dm2] | 45 |
| Controlled functions | S, V, K (2), M |
| Build difficulty | S0, S1 |
| Piloting difficulty | P2 |
Recommended power system and RC equipment
| Motor | *) C3548-750 |
| Speed controller | *) KAVAN R-50SB |
| Propeller blades | *) 11×8“ |
| Battery | 14,8V 2200mAh 30/60C, 14,8V 2600mAh 40/80C |
| Servos | *) 4× GO-17MG |
| RC system | Min. 6 channels (computer radio) |
| *) Included in the ARF set | |
11 items
This website is using cookies
In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.