Combo set Kavan C3536-1000 & Kavan R-40B
Wednesday 25.11. it can be at your place
Customer line 9 am - 6 pm: +420 774 590 258 | Do you need help?
| Price in e-shop with VAT: | 130,74 € |
| Temporarily unavailable | |
|
|
Send a question
on availability |
|
Send a question
on availability |
|
|
35 years in business = safe shopping and professional service |
|
Don't know how to choose? Are some parameters not clear to you? Write us your question and we will contact you with an answer.
#Chcete dostat upozornění ve chvíli, kdy produkt bude k dispozici? Stačí vyplnit formulář a náš hlídací pes Vám dá vědět.
Kit for a 3D aerobatic park flyer with a 1080 mm wingspan, made from virtually indestructible EPP foam. Thoroughly reinforced with carbon spars, it is designed for brushless motors with an output of 350–500 W. The wing has a symmetrical airfoil, while the fuselage has a large side area for excellent performance in 3D manoeuvres and knife-edge flight. Ailerons, rudder, elevator and motor speed are controlled.
A few hours with a bottle of cyanoacrylate glue are all it takes to complete this model, which can fly the manoeuvres of a classic F3A sequence as well as hover on the propeller and perform all the other 3D tricks!
It is also suitable for less experienced pilots. With reduced control throws, anyone with some aerobatic experience who can reliably fly loops, stall turns and rolls with a previous model can fly it. Thanks to the model’s low weight, any crashes are not too painful.
The one-piece wing with large ailerons has a symmetrical airfoil. Carbon spars provide strength, and servo bays are ready-cut. The fuselage has an airfoil section, with the horizontal part thoroughly reinforced with carbon strips and the vertical part featuring a large side area for excellent knife-edge flight performance.
The well-thought-out design includes a plywood motor mount, secured to the fuselage with carbon strips. Servo bays for the elevator and rudder are ready in the fuselage. The tail surfaces are also made of EPP. The two halves of the large full-flying elevator are attached to a carbon tube spar, which rotates in a 3D-printed bearing in the fuselage.
The ailerons, rudder and elevator are controlled by short carbon or steel pushrods. The main landing gear is made of carbon and has two lightweight wheels. It is attached to the supporting fibreglass plate, secured to the fuselage by 3D-printed plastic brackets, with 4 screws. The tail skid, with a 3D-printed mount and lightweight foam wheel, is linked to the rudder.
To control the model, you will need at least a 4-channel RC system (transmitter and receiver), which should offer at least dual and exponential rate adjustment.
For easy recreational flying, standard analogue micro servos with metal gears (e.g. Kavan GO-13MG, Hitec HS-65MG, etc.) are suitable. If you are serious about aerobatics, you should use powerful, fast digital servos with metal gears (e.g. Kavan GO-1013MG, Hitec HS-5065MG, etc.).
For power, we recommend a Kavan PRO 3536-1000, FOXY 3536-1000, Model Motors AXI 2814/16 V2 or similar brushless motor, with an APC 11×4,7SF propeller when powered by a 3S LiPo battery, or a 10×4,7SF propeller with a 4S LiPo.
The speed controller should be rated for at least 40 A. If you use powerful, fast digital servos, the speed controller should have a powerful switching BEC (e.g. Kavan PRO-40SB or Kavan R-50SB).
A 3S–4S LiPo battery with a capacity of 1300–1800 mAh and a discharge rating of at least 40C is suitable for powering the model.
Kavan Savage MAX was designed and is manufactured in the Czech Republic.
Package contents
The package contains printed fuselage, wing and tail surface parts, and landing gear covers cut from EPP foam, a plywood motor mount, 3D-printed plastic parts, carbon reinforcements, control horns, clevises, pushrods and other small accessories. The carbon landing gear with lightweight wheels and a detailed illustrated assembly manual are also included.
Notice: Under Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems, and Commission Implementing Regulation (EU) 2019/947 of 24 May 2019 on the rules and procedures for the operation of unmanned aircraft, operators and pilots of unmanned aircraft (traditional model aircraft, multicopters, drones) weighing more than 250 g or carrying a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic, with the Civil Aviation Authority). For further information, see: Registration of drone operators and pilots.
13 items
This website is using cookies
In order to improve our services, we use cookies on this website. For more information go to Terms and conditions for use of website.